Experimental and theoretical assessment of Fe-doped indium-oxide-based dilute magnetic semiconductors

Specimens of iron-doped indium oxide (In_1-xFe_x)₂O₃ with x?=?0.015, 0.03, 0.045 and 0.06, amalgamated through a traditional solid-state reaction method followed by H₂/air sintering, were characterised using an X-ray diffractometer (XRD), a vibrating sample magnetometer (VSM), and a scanning electron microscope (SEM) to investigate their structural, magnetic and morphological properties respectively. According to XRD plots, all the specimens exhibit cubic bixbyite structures along with ancillary phases. Magnetic assessment showed that In₂O₃ has a negative susceptibility, exhibiting diamagnetic behaviour at room temperature. The doping of Fe ions induces ferromagnetic (FM) ordering, which is enhanced with increasing doping content. The strength of the magnetisation increases when the specimens are exposed to H₂ but is reduced on further air sintering. A bound magnetic polaron (BMP) model is successfully fitted to the observed FM data involving localised carriers and magnetic cations. A multivariate assessment viz. a hierarchical cluster analysis (HCA) was used to corroborate and strengthen the experimental determined magnetic properties. A homogeneous particle distribution was observed in all SEM micrographs and is validated through MATLAB-based simulation by applying a watershed segmentation algorithm. Surface plots also confirm the change in magnetic properties with increase in doping concentration.     

S‐Nitrosoglutathione‐Based Nitric Oxide‐Releasing Nanofibers Exhibit Dual Antimicrobial and Antithrombotic Activity for Biomedical Applications

The novel use of nanofibers as a physical barrier between blood and medical devices has allowed for modifiable, innovative surface coatings on devices ordinarily plagued by thrombosis, delayed healing, and chronic infection. In this study, the nitric oxide (NO) donor S‐nitrosoglutathione (GSNO) is blended with the biodegradable polymers polyhydroxybutyrate (PHB) and polylactic acid (PLA) for the fabrication of hemocompatible, antibacterial nanofibers tailored for blood‐contacting applications. Stress/strain behavior of different concentrations of PHB and PLA is recorded to optimize the mechanical properties of the nanofibers. Nanofibers incorporated with different concentrations of GSNO (10, 15, 20 wt%) are evaluated based on their NO‐releasing kinetics. PLA/PHB + 20 wt% GSNO nanofibers display the greatest NO release over 72 h (0.4–1.5 × 10^?10 mol mg^?1 min^?1). NO‐releasing fibers successfully reduce viable adhered bacterial counts by ≈80% after 24 h of exposure to Staphylococcus aureus. NO‐releasing nanofibers exposed to porcine plasma reduce platelet adhesion by 64.6% compared to control nanofibers. The nanofibers are found noncytotoxic (>95% viability) toward NIH/3T3 mouse fibroblasts, and 4′,6‐diamidino‐2‐phenylindole and phalloidin staining shows that fibroblasts cultured on NO‐releasing fibers have improved cellular adhesion and functionality. Therefore, these novel NO‐releasing nanofibers provide a safe antimicrobial and hemocompatible coating for blood‐contacting medical devices.     

Synthesis of nanoscale zero‐valent iron modified graphene oxide nanosheets and its application for removing tetracycline antibiotic: Response surface methodology

Nowadays, pharmaceutical antibiotics are known as a serious class of pollutants. Therefore, it is important to develop effective methods for removing these pollutants from aqueous media. Different methods were applied for this purpose, and among these methods, chemical reduction by a cheap and eco‐friendly nanocatalyst is the most efficient and simplest method. In this research, based on graphene oxide supported by zero‐valent iron in mono‐, bi‐, and tri‐metallic systems, various nanocomposites were synthesized and used to degrade tetracycline as a model antibiotic from aqueous media. An investigation was carried out on the synergic effect among graphene oxide and the nano zero‐valent iron‐based tri‐metallic system as well as removal efficiencies. It was found that higher degradation efficiency is yielded by graphene oxide supported by Fe/Cu/Ag tri‐metallic system. The maximum synergic effect occurs at an acidic medium. The Brunauer–Emmett–Teller, Fourier transform spectroscopy, scanning electron microscopy‐energy dispersive X‐ray analysis, transmission electron microscopy, and X‐ray diffraction analysis were used to characterize the synthesized nanocomposites, which has successfully proved the loading of nanoscale Fe/Cu/Ag tri‐metallic on a graphene oxide support. The central composite design was used to model and optimize all involved variables affecting antibiotic removal efficiency. The consequences illustrated the optimum condition regarding the removal of 50 ppm of tetracycline, for the nanocomposites dose of 3.0 mg ml^?1, the contact time of 30 min, and pH of 2, was achieved using the simplex non‐linear optimization method. Moreover, antibiotic adsorption kinetic models were also investigated. Finally, the tetracycline removal from aqueous media at different concentrations, 25, 50, and 75 ppm, was successful by applying the proposed nanocomposite, and the results showed tetracycline removal efficiencies of above 70%.     

Crosslinking network of bio‐based bis‐functional epoxides derived from trans‐limonene oxide

The thiol‐ene reaction between trans‐limonene oxide (trans‐LO) and ethane‐1,2‐dithiol in the presence of triethylborane affords a bio‐based bis‐functional epoxide (bis‐trans‐LO). The crosslinking reaction of bis‐trans‐LO with branched polyethyleneimine (BPEI; M_n = 600; BPEI₆₀₀) at a feed ratio of bis‐trans‐LO/BPEI₆₀₀ = 57/43 (wt/wt) yields the corresponding network polymer with T_d10 (10% thermal decomposition temperature) of 304.7 °C in 98% yield. In contrast, negligible amounts of network polymer are obtained by the reaction of bis‐LO (bis‐functional epoxide derived from cis and trans‐LO) and BPEI₆₀₀ regardless of the feed ratio. The mechanical strengths as measured by direct tensile tests of the network polymers derived from bis‐trans‐LO and BPEI_600,1800 (M_n = 600 and 1800) were approximately 16 and 11 times higher than that of bis‐LO and BPEI₁₈₀₀, respectively. The tensile shear strengths of the metal‐to‐metal adhesive bonds induced by bis‐trans‐LO and BPEI_600,1800 were 9.5 and 14.1 MPa, respectively. DMA revealed that the storage modulus of the network polymer derived from bis‐trans‐LO and BPEI₁₈₀₀ in the rubber region was higher than that of the material prepared from bis‐LO and BPEI₁₈₀₀, indicating higher crosslink density of the bis‐trans‐LO/BPEI₁₈₀₀ system. © 2019 Wiley Periodicals, Inc. J. Polym. Sci., Part A: Polym. Chem. 2019 , 57, 2466–2473     

Cobalt Based Nanoparticles Embedded Reduced Graphene Oxide Aerogel for Hydrogen Evolution Electrocatalyst

Efficient water electrolysis catalyst is highly demanded for the production of hydrogen as a sustainable energy fuel. It is reported that cobalt derived nanoparticle (CoS₂, CoP, CoS|P) decorated reduced graphene oxide (rGO) composite aerogel catalysts for highly active and reliable hydrogen evolution reaction electrocatalysts. 7 nm level cobalt derived nanoparticles are synthesized over graphene aerogel surfaces with excellent surface coverage and maximal expose of active sites. CoS|P/rGO hybrid aerogel composites show an excellent catalytic activity with overpotential of ≈169 mV at a current density of ≈10 mA cm^?2. Accordingly, efficient charge transfer is attained with Tafel slope of ≈52 mV dec^?1 and a charge transfer resistance (R_ct) of ≈12 Ω. This work suggests a viable route toward ultrasmall, uniform nanoparticles decorated graphene surfaces with well‐controlled chemical compositions, which can be generally useful for various applications commonly requiring large exposure of active surface area as well as robust interparticle charger transfer.     

GOSs-稀土配合物紫外增强材料的光谱分析与稳定性研究

氧化石墨烯薄片(GOSs)作为一种新型的二维片状材料,具有较高的比表面积、丰富的表面含氧官能团以及良好的光热稳定性。而稀土配合物通过无机稀土元素与有机配体的结合表现出优异的荧光特性。为了将两类材料具有的物化特性结合起来应用于紫外光谱探测领域。选取了合适的有机配体啉菲罗啉(1,10-邻二氮杂菲,phen)、2’2-联嘧啶(bpm)作为桥联分子,把氧化石墨烯(GOSs)与稀土配合物通过氢键自组装作用进行复合,制备了高效稳定可调的GOSs-稀土配合物复合荧光材料GOSs-Eu(BA)3phen和GOSs-Eu(TTA)3bpm,并且制备了相应的聚乙烯醇(PVA)共混紫外增强薄膜,对其光谱特性与稳定性进行了深入的研究。采用红外光谱、扫描电镜和金相显微镜等方法,对紫外增强材料进行了性能表征。采用吸收光谱,荧光光谱等方法,对紫外增强薄膜进行了性能表征。此外,通过热重测试(TGA)表征了GOSs氢键复合前后紫外增强材料的热稳定性,通过荧光强度-紫外光照次数表征了GOSs氢键复合前后紫外增强薄膜的光稳定性。红外光谱分析发现,进行配位前后有机配体的特征峰产生了频移,表明稀土配合物中Eu 3+与配体之间存在着明显的配位作用。在进行复合之后,桥联配体的特征峰也产生了偏移,表明GOSs与稀土配合物通过桥联分子的氢键作用进行了进行复合。吸收光谱与荧光光谱测定结果表明增强薄膜吸收峰在200~400 nm,荧光主峰在612 nm左右,为Eu 3+特征红色荧光峰,且不同配体可以实现不同范围的吸收产生差异化的荧光表现。扫描电镜和金相显微镜清晰地展示了稀土配合物复合前后的微观形貌,即颗粒状稀土配合物附着在石墨烯薄片上。光稳定性测试表明经过GOSs氢键复合之后,Eu(BA)3phen和Eu(TTA)3bpm稀土配合物荧光材料在进行25次荧光强度测试后光漂白程度分别下降了4.26%和6.41%,提高了其光稳定性。热重测试也表明在经过GOSs氢键复合之后,稀土配合物的热稳定性有了很大提高。总之,得益于GOSs和稀土配合物的特性结合,所制备的紫外增强材料表现出优异的荧光特性与稳定性,必将在紫外探测方面有着广阔的应用前景。     

A novel scheme to acquire enhanced up-conversion emissions of Ho3+ and Yb3+ co-doped Sc2O3

A detailed investigation about the effect of Sc₂O₃: 1 mol%Ho³⁺/5 mol%Yb³⁺ co-doped with Ce⁴⁺ ions prepared by sol-gel methods was performed systematically. Under the excitation of 980 nm laser diode, both green emission (553 nm, ⁵F₄/⁵S₂→⁵I₈) and red emission (672 nm, ⁵F₅→⁵I₈) were both observed in the emission spectra of the samples, which were found to be two-photon process and sensitized by Yb³⁺ ions. With the increasing of Ce⁴⁺ ions, the up-conversion green emission intensity are increased by 6.52, 8.69, 10.85, 13.92 and 16.66 fold, corresponding to the Ce⁴⁺ ions concentrations from 5 mol% to 13 mol%, respectively. The number of photons are necessary to populate the upper emitting state decreases to 2 and the infrared absorption coefficient is reduced, when the Ce⁴⁺ ions concentration increase to 13 mol%. Ce⁴⁺ ions play an important role in tailoring the local crystal field around Ho³⁺ ions, lowering the highest phonon cut-off energy of matrix and reducing the infrared absorption coefficient, thus hindering the non-radiative processes, which contribute to the increased emission intensity. The excellent enhancement makes it a promising multifunctional optical luminescence material.     

Microstructure evolution of room-temperature-sputtered ITO films suitable for silicon heterojunction solar cells

Thickness influence on structural, optical and electrical properties of sputtered indium tin oxide (ITO) with thickness ranging from 60 up to 430 nm films has been studied. At the increase of the film thickness crystallinity degree and grain size increased, whereas tensile structural distortion as well as resistivity decreased. It was observed that a microstructure evolution takes place: the initial amorphous layer evolved in polycrystalline phase, with a grain–subgrain surface morphology. Carrier concentration increased at the increase of the film thickness and a general relationship between electrical characteristics and structural distortion has been found. In thinner films larger tensile distortion allowed to include larger amount of interstitial O and/or Sn atoms in the lattice. An appreciable impact of the thickness was also observed on electro-optical properties in terms of changes in energy gap, resistivity and optical absorption. Silicon heterojunction solar cells have been produced and J_sc as high as 33.0 mA/cm² has been obtained.     

Photosensitive organic-inorganic hybrid structures based on porous silicon

Abstract

In this study, the photovoltaic organic-inorganic structures were created by deposition of poly(3,4-ethylenedioxythiophene) film doped by poly(styrenesulfonate) and reduced graphene oxide on the porous silicon/silicon substrate. Formation of the hybrid structure was confirmed by means of atomic-force microscopy and Fourier transform infrared spectroscopy. The current-voltage characteristics of the obtained structures were studied. It was found the increase of electrical conductivity and photo-induced signal in organic-inorganic structures. Temporal parameters and spectral characteristics of photoresponse in the 400–1100?nm wavelength range were investigated. The widening of spectral photosensitivity in a short-wavelength range due to light absorption in various layers of the multijunction structure in comparison with single crystal silicon was revealed.